How-to · Technical Analysis
50-Day / 200-Day Crossover: Golden Cross Screener Settings
A golden cross screener turns the 50-day / 200-day crossover into a short list you can work through each evening. The scan finds the cross; the filters and the ranking decide which names deserve a chart.
Short answer
Set the scan to daily bars, require the 50-day simple moving average to have crossed above the 200-day within the last few sessions, then add a liquidity floor, price above both averages, a cap on distance from the 200-day and a check that earnings are not days away. Rank what remains and confirm each chart by hand before any order.
Most evenings, a scan for the cross returns either nothing or far too much. A quiet market gives you an empty screen. After a broad rally the same scan returns pages of names, many of them thinly traded, some already stretched well above both lines, and a few reporting earnings in two days. The cross condition is only the first line of the scan. The golden cross and death cross definition explains what the signal records. The rest of the scan settings exist to throw out bad hits.
How do you set up the scan, step by step?
- Pick the universe: US-listed common stocks and plain ETFs, on daily bars. Leave out leveraged and inverse funds, whose daily reset distorts long averages.
- Write the cross condition. Most screeners offer a “crosses above” function: 50-day SMA crosses above 200-day SMA, within the last few bars. If yours only has a ratio, use the 50-day divided by the 200-day, set between 1.00 and a little over it, and add yesterday’s ratio below 1.00 if the tool allows a prior-bar value.
- Fix the average type. Use simple averages of daily closes, matching the chart you will read later, since exponential averages cross earlier and give different dates for the same stock.
- Add a liquidity floor. Filter on average daily dollar volume, which is average share volume times price, and set the floor at a level where your normal order is a small fraction of a day’s trading.
- Require price above both averages. A cross with the last close sitting back under the 50-day is already fading.
- Cap the distance from the 200-day. Measure it in percent, or better in average true range units, and drop names stretched far above it.
- Add an earnings field. Show the next report date as a column so you can sort or exclude.
- Save it and run it at the same time each day, after the close.
A stock needs 200 sessions of history before it has a 200-day average at all. Recent listings and spin-offs will never appear on the list, however strong their charts look.
What do the numbers behind a fresh cross look like?
Screeners recompute both averages each day by dropping the oldest close and adding the newest. That rolling update is easy to check by hand, and it shows how thin the margin on cross day usually is.
The cross happened by nine cents. That is thin, and a single soft close tomorrow could undo it. And the stock printing the cross is already almost five ATRs above the 200-day, which means a stop placed under the long average would sit a long way from the entry. The moving average calculator will run both averages over a longer series if you want to check a screener’s figures against your own.
Why check the earnings date before a fresh cross?
A cross is a slow reading of months of closes. An earnings report is a single overnight event that can open the stock far from its last price, and if that report lands three sessions after the cross, the gap decides the trade long before the trend has a chance to, which makes the cross close to irrelevant for that position.
So screen for it. Exclude any name reporting within your planned holding period, or flag it and treat it as a separate decision. The checks for holding through a report are covered in the earnings season checklist. A cross that arrives just after a report is a different case. The gap is already in the averages, and the next report is weeks away.
How should you rank what the scan returns?
Sort the survivors so the best candidates sit at the top. Useful orders:
| Rank by | Prefer | Why |
|---|---|---|
| Days since the cross | Fewer | The trend reading is fresh and the stock has had less time to run |
| 200-day slope | Rising or flat-to-rising | A 50-day crossing a 200-day that is still falling describes a bounce inside a downtrend |
| Distance from the 200-day, in ATRs | Smaller | A nearer long average allows a tighter, more sensible stop |
| Strength against a broad index | Stronger | A stock already leading the market leans less on the index to keep rising |
| Nearby price structure | A base just under resistance | Gives a defined entry trigger on a break above it |
No single column settles it. A name that is fresh, above a rising 200-day and close to it in ATR terms is worth a chart tonight, while one that crossed over a week ago, under a 200-day still sloping down, and now trades several ATRs above it has already given you most of the reasons in the table for passing. Let it go.
What should you check before acting on a hit?
Every hit still needs a chart. Open each one and work down this list:
- The cross is real on your chart, with simple averages, and the price history has no unadjusted split or data spike.
- Price closed above both averages, and the 50-day is turning up.
- No earnings report falls inside your holding period.
- There is an entry trigger on the daily chart: a pullback toward the 50-day that holds, or a breakout above a nearby level on rising volume.
- The stop has a logical place, and its distance in ATRs gives a position size you accept.
- The name does not duplicate a position you already hold in the same sector.
The cross can also flip back within days, especially when the averages ran flat and close together before it. Those reversals, and how to filter for them, are the subject of golden cross false signals.
How does a death cross screen differ?
Flip the conditions. The 50-day crosses below the 200-day, price closes under both averages, and the 200-day is flat or falling. Same liquidity floor, same earnings column, same ranking by recency and ATR distance, reversed.
Shorting brings its own checks. It depends on shares being available to borrow, and borrow availability and its cost vary by broker and by name, so add a column for it if your platform shows one, or check before you plan the trade. Thin names matter more on the short side, where a squeeze in a stock with little volume can move against you faster than a stop can fill. And after a broad selloff a death cross scan can return a long list all at once, as sector after sector rolls over, which tells you more about the market than about any one stock on it.
The death cross list also works as a filter on longs. Names on it come off the watchlist.
Questions traders ask next
How many days back should a golden cross scan look?
Long enough to catch crosses you missed, short enough that the move is still young. A window of a few sessions suits a scan you run every evening. Weekly reviewers can widen it to the past week or two. Past that, the stock has usually left the averages behind, and the list fills with names that crossed long ago.
Can I screen ETFs for a golden cross the same way as stocks?
Yes. Any fund with 200 sessions of daily closes has both averages, so the same condition works. Keep leveraged and inverse funds out of the universe, since their daily reset bends the long averages. Broad index funds cross rarely, so a scan of plain sector and index ETFs will often return an empty list.
Why does my screener show a cross the chart does not?
The usual causes are a different average type, a different data source, or a price history that was not adjusted for a split or a large special dividend. An unadjusted split can drag the 200-day so far that a false cross appears. Open the chart, confirm both lines are simple averages of daily closes, and check for a gap that looks like a split.